The Scan Premier FFP1 Valved Disposable Dust Masks are lightweight filtering facepiece respirators designed to provide basic respiratory protection against suitable low-level airborne particulate hazards.

Featuring a moulded construction made from the filter material itself, these disposable respirators are designed to cover the nose, mouth and chin, helping reduce the inhalation of airborne particles when correctly fitted.

An integrated exhalation valve helps reduce breathing resistance during exhalation, while the adjustable nose clip, soft foam nose piece and elasticated retaining straps help provide a secure, comfortable fit.

The masks also feature a non-irritating inner facepiece designed to improve comfort during routine work.

Specified as conforming to EN149:2001+A1:2009, these masks have an FFP1 protection classification, making them suitable for appropriately assessed tasks involving low levels of non-toxic dust and other particulate contaminants within the limits of their certification.

Potential applications include certain low-dust DIY, maintenance and hand-sanding tasks where a risk assessment confirms that FFP1 protection is sufficient.

Important: FFP1 is the lowest of the three EN149 filtering facepiece protection classes. It is not suitable for every construction dust hazard, and tasks involving respirable crystalline silica, hazardous fibres or other harmful substances may require substantially higher protection.

Key Benefits

• Scan Premier valved disposable dust masks

• FFP1 particulate respiratory protection classification

• Stated conformity to EN149:2001+A1:2009

• Moulded filtering facepiece construction

• Designed to cover the nose, mouth and chin

• Integrated exhalation valve

• Elasticated retaining straps

• Adjustable nose clip for improved fitting

• Soft foam nose piece

• Non-irritating inner facepiece

• Lightweight disposable design

• Suitable for appropriately assessed low-level particulate exposure

• Practical for certain DIY and maintenance tasks

• Designed for single-shift use, subject to condition and manufacturer instructions

FFP1 Particulate Respiratory Protection

The Scan Premier FFP1 Dust Masks are classified as FFP1 filtering facepiece respirators.

Under EN149, FFP1 is the basic protection class for disposable particulate respirators.

An FFP1 respirator is tested to provide a minimum 80% filtration efficiency against the specified test aerosols under laboratory conditions.

However, this filtration figure does not mean the wearer is guaranteed an 80% reduction in exposure.

Actual protection depends on correct selection, facial fit, a suitable seal, wearing time and workplace conditions.

In UK workplace guidance, FFP1 respirators are generally associated with an assigned protection factor (APF) of 4, where the respirator is suitable, correctly fitted and used as part of an appropriate respiratory protection programme.

Important: FFP1 respirators are not appropriate for all harmful dusts. Always select respiratory protective equipment according to the substance involved and the exposure assessment.

Integrated Exhalation Valve

The masks feature an integrated exhalation valve designed to make breathing out more comfortable.

The valve allows exhaled air to leave the mask more easily, helping reduce moisture and heat build-up during use.

This can improve comfort when carrying out suitable physical tasks.

Important: The valve is designed for wearer comfort. Valved respirators should not be relied upon for source control where filtering the wearer's exhaled breath is required.

Moulded Filtering Facepiece Design

The Scan Premier FFP1 Masks feature a moulded construction made from the filtering material itself.

This provides a lightweight, compact respiratory protective device without the need for a separate rigid filter housing.

The mask is designed to cover the:

• Nose

• Mouth

• Chin

A secure facial seal is essential for effective respiratory protection.

Facial hair, incorrect positioning and unsuitable mask sizing can substantially reduce the protection achieved.

Adjustable Nose Clip

Each mask incorporates an adjustable nose clip.

This allows the upper edge of the respirator to be shaped around the bridge of the nose.

Correct adjustment helps improve the fit and reduce gaps where unfiltered air could enter.

The nose clip should be adjusted according to the manufacturer's fitting instructions.

Soft Foam Nose Piece

The soft foam nose piece provides additional comfort around the nose.

It helps cushion the contact area between the mask and the face.

Combined with the adjustable nose clip, this feature supports a more comfortable fit during suitable work activities.

However, comfort alone does not confirm that an adequate respiratory seal has been achieved.

Elasticated Retaining Straps

The Scan FFP1 Valved Masks feature elasticated retaining straps designed to hold the respirator securely in place.

Correct strap positioning is important for maintaining the mask's fit.

The straps should be fitted according to the manufacturer's instructions and checked before entering an area where respiratory protection is required.

Do not modify, knot or reposition the straps in a way that compromises the mask's seal.

Non-Irritating Inner Facepiece

The masks incorporate a non-irritating inner facepiece designed for additional comfort.

This is particularly useful during tasks where a disposable respirator needs to be worn for an extended period.

The lightweight construction, foam nose piece and exhalation valve work together to improve wearing comfort.

Users should stop wearing the mask if it causes irritation or cannot be fitted securely.

Suitable Applications

The Scan Premier FFP1 Disposable Masks may be suitable for certain low-level particulate exposures, depending on the material and working conditions.

Potential applications include:

• Suitable low-dust DIY tasks

• General household maintenance

• Certain hand-sanding operations

• Low-risk workshop activities

• Other tasks where an assessment confirms FFP1 protection is sufficient

The supplied product information also mentions brick dust, concrete, plaster and loft insulation.

Important: These materials can present significant respiratory hazards. Cutting, drilling or sanding brick and concrete can generate respirable crystalline silica, while insulation materials may release fibres or other hazardous particles.

FFP1 should not be assumed adequate for these tasks. Follow the relevant safety guidance and use a higher-rated respirator or other controls where required by the risk assessment.

Understanding FFP1, FFP2 & FFP3

Disposable filtering facepiece respirators are classified under EN149 according to their tested performance.

The assigned protection factors shown are commonly used in UK workplace respiratory protection guidance and depend on correct selection, fitting and use.

Important: FFP classes are not defined by simple particle-size bands such as larger than 5 microns, 2–5 microns or smaller than 2 microns. The appropriate class depends on the hazard, exposure level and required protection factor.

FFP1 – Basic Particulate Protection

FFP1 respirators provide the lowest protection class under EN149.

They may be suitable for certain low-level particulate hazards where the required protection factor does not exceed their capability.

FFP2 – Higher Particulate Protection

FFP2 respirators provide a higher level of tested filtration performance.

They are used for appropriately assessed particulate hazards requiring greater protection than FFP1.

FFP3 – Highest EN149 Filtering Facepiece Class

FFP3 respirators provide the highest tested filtration performance among the three EN149 filtering facepiece classes.

They are often selected for more hazardous particulate exposures, subject to a suitable risk assessment and correct fit.

No FFP class provides protection against gases or vapours unless a separate appropriate filter system is used.

EN149:2001+A1:2009 Certification

The Scan Premier FFP1 Valved Disposable Masks are specified as conforming to EN149:2001+A1:2009.

EN149 is the European standard covering filtering half masks designed to protect against particles.

The standard establishes requirements relating to matters such as filtration performance, breathing resistance and inward leakage.

The supplied information confirms the FFP1 class, but does not specify the full additional markings, such as NR, R or D.

Check the mask and packaging for the complete certification markings and the manufacturer's declaration of conformity before workplace use.

How to Fit the Scan FFP1 Mask

Correct fitting is essential to achieve the intended protection.

1. Inspect the mask for damage before use.

2. Position the moulded respirator over the nose, mouth and chin.

3. Secure the elasticated straps according to the manufacturer's instructions.

4. Adjust the nose clip to follow the bridge of the nose.

5. Check that the mask sits securely against the face.

6. Perform the user seal check described in the manufacturer's instructions.

7. Reposition the mask if leakage is detected.

For workplace use, tight-fitting respiratory protective equipment generally requires a suitable face-fit test for the individual wearer.

Important: Facial hair in the sealing area can prevent an effective fit.

Disposable & Single-Shift Use

The supplied instructions state that the masks should be disposed of after each period of work or an 8-hour shift.

Replace the mask sooner if it becomes:

• Damaged

• Heavily contaminated

• Wet or excessively soiled

• Difficult to breathe through

• Unable to maintain an adequate facial seal

The stated eight-hour period is a maximum use guideline, not a guarantee that a mask will remain suitable for an entire shift.

Always follow the manufacturer's instructions and any applicable workplace respiratory protection procedures.

Respiratory Safety Precautions

The Scan Premier FFP1 Masks are designed for particulate protection within their stated classification.

They are not suitable for protection against:

• Oxygen-deficient atmospheres

• Toxic gases

• Solvent vapours

• Carbon monoxide

• Unknown airborne contaminants

• Hazards requiring a higher protection factor

• Environments where an air-supplied respirator is necessary

Do not use these masks for asbestos work, significant silica dust exposure or other high-risk respiratory hazards unless a competent assessment specifically establishes that the equipment is suitable.

Engineering controls, dust extraction and safe working methods should be used alongside appropriate respiratory protection.

Why Choose Scan Premier FFP1 Valved Disposable Masks?

The Scan Premier FFP1 Valved Disposable Masks offer a lightweight respiratory protection option for appropriately assessed low-level particulate hazards.

Their moulded filtering facepiece construction provides a practical disposable design, while the exhalation valve helps improve breathing comfort.

The adjustable nose clip, soft foam nose piece, elasticated retaining straps and non-irritating inner facepiece support a comfortable and secure fit.

With stated conformity to EN149:2001+A1:2009, these masks provide a defined FFP1 level of particulate protection when correctly selected and fitted.

For suitable DIY, workshop and maintenance tasks requiring basic particulate respiratory protection, the Scan Premier FFP1 Masks are a practical option.

Product Information

Brand: Scan
Product: Premier FFP1 Valved Disposable Masks
Type: Disposable Filtering Facepiece Respirator
Respiratory Protection Class: FFP1
Stated Standard: EN149:2001+A1:2009
Minimum Tested Filter Efficiency: 80%
Typical UK Assigned Protection Factor: 4
Mask Design: Moulded Filtering Facepiece
Face Coverage: Nose, Mouth and Chin
Valve: Integrated Exhalation Valve
Retaining Straps: Elasticated
Nose Adjustment: Adjustable Nose Clip
Nose Cushion: Soft Foam
Inner Facepiece: Non-Irritating
Use Duration: Dispose of After Each Work Period or Maximum 8-Hour Shift, Subject to Condition and Instructions
Suitable Applications: Appropriately Assessed Low-Level Particulate Exposure
Full NR/R/D Marking: Not Specified
Pack Quantity: Not Specified
Colour: Not Specified

Please note: The complete EN149 markings, pack quantity and colour have not been supplied. FFP1 respirators are not suitable for every construction dust hazard. Confirm the exposure risks, required protection level and fit before use.

Data Sheets:
Data Sheet
Data Sheet
Data Sheet
Data Sheet
Data Sheet
Data Sheet

WEEE Recycling Producer Registration Number:12889

How do I return my old product to be recycled?

You can return your old product to MyDIY. Waste Electrical and Electronic Equipment (WEEE) is taken back free of charge on a one-for-one, like-for-like basis. Waste batteries including rechargeable batteries are taken back free of charge. You are not obliged to make any purchase when returning old batteries. Each local authority must also accept household WEEE and small batteries free of charge at its recycling facilities. All WEEE and waste batteries must be recycled and should not be placed in any of your household wheelie bins. Make sure you always recycle all your old electrical goods and batteries.

What products can I recycle for free?

You can return anything that is electricaly powered or battery powered. Even your old bicycle lamps can be recycled!.

Do you take back used batteries?

Yes we do. The batteries that we accept are AA, AAA, C or D, powertool batterys and also the flat batteries that are found in watches and toys. Unfortunately we do not accept back any Industrial or car batteries.

Do I need to have made a purchase at MyDIY.ie?

No you don't. You can recycle any of the above items at our store in Inchicore Dublin 8, even if you have not made a purchase with us.

Will you collect my old product?

Yes, but we must be notafied within 14 days of purchase date. You can still arrange to have your old appliance recycled free of charge. Simply bring it back to our Inchicore store and we will ensure that it is disposed of in an environmentally friendly manner.

How much will it cost?

There is no charge to return products to any of our warehouses.

Why should I recycle with MyDIY?

We will ensure that your old product is disposed of correctly to reduce the potentially harmful effects caused on the environment and to conserve natural resources. Further information can be found on weeeireland.ie.

EMC (Environmental Management Cost) Included in the purchase price. 

Gas discharge lamps, LFLs and CFLs €0.15

LED lamps and luminaires €0.05

Large appliances €5.00

Information

Fast & Reliable Shipping with DPD

We ship all orders via DPD, one of Ireland’s most trusted couriers. With DPD’s one-hour delivery window, you won’t have to wait around all day for your MyDIY.ie order!

Delivery Times

Each product on our website is marked with an estimated delivery time. If you order multiple items, your order will arrive based on the item with the longest delivery time. For example, if you buy two next-day items and one 3-day item, the entire order will arrive in 3 days.

While most products arrive in 1-2 days, we offer over 44,000 items, so please allow 4-5 working days for some deliveries. Need it faster? Call us at 01-446692, and we'll do our best to help.

Delivery Charges

• FREE delivery for orders over €150 within Ireland.

• Orders under €150: €8.99 delivery fee.

• International delivery: Charges based on weight—contact us for a quote.

When Will I Receive My Order?

• Most orders ship on a 24-hour courier service (2 working days).

• Larger orders may take 4-5 days, and pallet deliveries require scheduling.

• Orders placed before 2 PM usually ship within 24 hours.

• Orders after 1:30 PM Friday or on weekends ship the following week.

• Busy holiday periods may cause slight delays beyond our control.

Do I Need to Be Home for Delivery?

Yes, someone must sign for deliveries due to item value. If you're not home, DPD will leave a card with re-delivery or collection instructions. After two failed attempts, your order may be returned to us, and a re-delivery fee may apply.

Damaged or Incomplete Orders

We carefully pack all orders, but if something arrives damaged or incomplete, contact us within 24 hours. Report shortages within 3 days of delivery.

International Shipping

We ship to Europe and worldwide, with charges based on weight. Liquid products cannot be shipped internationally due to regulations. Contact us for a quote—we're happy to help!

Customer Service & Returns